Project Description

BLDC Motor Driver

NSPBLDS4805 brushless DC motor driver is the latest high-tech product of our company for medium-power brushless motor. This product uses a large-scale integrated circuit to replace the original hardware design, with higher anti-interference and fast response. This product is suitable for driving any three-phase brushless DC motor, Hall or no Hall sensor, with peak current below 5A and power supply voltage between DC10V~50V. This driver features low temperature operation at high current. The products are used in a series of electrical automation control fields such as knitting equipment, medical equipment, food packaging machinery and electric power tools.


Current loop design, high torque at low speed, smooth operation

High torque high speed output, the maximum speed reaches 10000rpm/min(depend on speed of motor)

Speed control: 0-5V analog , PWM(10Hz-500Hz)

With signal input terminals EN (start/stop), DIR (direction)

With protection function of over current, over voltage, under voltage and motor block

This product can achieve the following functions

Speed open loop operation with hall sensor

Speed close loop operation with hall sensor

Speed open loop operation without hall sensor

Speed close loop operation without hall sensor

The above functions can be set directly on the drive panel.(Hall or without hall can be identified automatically)

Electrical Performance

(Ambient Tj=25℃)

Power supplyDC10V~50V
Rated current≤5A
Rated powerMax 288W
Insulation resistance﹥500MΩ  at normal temperature
Insulation strength0.5KV, 1min at normal temperatures and pressures

Working Environment

Coolingnatural cooling or forced air cooling
Working environmentSituation avoid dust, oil mist and corrosive gases
Humidity﹤80%RH, no condensation, no frost
vibration﹤0.5G(4.9m/s2 )10Hz-60Hz, non-continuous operation
Storage temperature-20℃~+65℃
[Note] Due to the drastic changes in the temperature of the storage and transportation environment, condensation or frosting is likely to occur. The driver only can be powered on when the temperature of the driver is consistent with the ambient temperature after being placed in this environment for more than 12 hours.

Instructions for the terminal

Function Mark Description
 Control+5Vpower supply positive(Built-in power output)
VSPExternal speed control signal, 0-100% of the motor speed adjustment through external potentiometer to change VSP voltage, 0~5V
DIRMotor CW/ CCW rotation control ,CCW when connect DIR to GND,CW when not connect DIR to GND
ENMotor enable control, EN is connected to GND, allowing the drive to run; EN is not connected,prohibiting the drive from running.
GNDControl signal power ground
Hall+5V Hall power supply positive
HA Hall sensor signal A phase input
HB Hall sensor signal B phase input
HC Hall sensor signal C phase input
GND HALL power ground
Motor and powerU、V、Wmotor three-phase output signals
GND、V+ DC10V~50V power supply input


Speed control mode (VSP)1. Connect with external potentiometer to adjust speed: connect the two fixed ends of the external potentiometer (5K~10K) to the GND and +5V terminals of the driver respectively. By connecting regulating terminal to the VSP terminal. The speed can be controlled by external potentiometer, or inputting analog voltage to VSP terminal through other control units (such as PLC, MCU, etc.). The voltage range of the VSP port is DC 0V~+ 5V, corresponding to the speed of motor from 0 to max speed.
2. Input PWM signal to adjust speed: connect PWM signal positive terminal to VSP terminal and negative terminal to GND. By setting the +5V PWM signal with the frequency of 10Hz-500Hz, through PWM duty cycle change to achieve speed adjustment.

CW/ CCW rotation


By controlling the high and low level transitions of DIR terminal to control rotation of the motor.

Note: In order to avoid huge impact to motor and mechanical equipment when motor changes direction suddenly at high speed, the drive decelerate the motor until it stops when DIR terminal receives commutation signal, then the motor changes direction and accelerates to the set speed.




By controlling the high and low level transitions of EN terminal to control RUN/STOP of the motor. Motor runs normally when EN is in low level and stops when in high. When the start/stop is used to control the motor to stop, the motor stops naturally. Its motion law is related to load inertia. Factory setting is EN for allowed operation.

Detailed error codes table

Indicator lightDescriptionNote
1stop one time when flickering twiceUnder  voltage Fault
2stop one time when flickering three timesOver voltage Fault
3stop one time when flickering four timesOver current Fault
4stop one time when flickering five timesBlock rotation faultThe motor is not running or the motor wire is not connected
5stop one time when flickering six timesshort circuit faultMotor coil open circuit or motor wire open circuit

Wiring diagram